Skip to main content

Walther CCP Review

Walther CCP Review
Photos by Sean Utley

If you stick around in the gun arena long enough, you realize that things go in waves. A while back, if you didn’t offer your pistol in .40, you couldn’t sell it. Then, the more bullets it held, the more of them you’d sell, and if the number wasn’t close to a dozen-and-a-half, you were considered to be slackers.

Now it’s concealment. We’ve gone from “I have to have a veritable bushel of bullets” to “Can’t you make it any smaller/lighter/easier to conceal?” Of course, when we were lusting after magazines that held a third of a box of ammo, they were hard to find and expensive, and they weren’t making new ones. Now, with every other person you know carrying a handgun, concealed is the new black.

Walther knows this. That’s why it spent a lot of time, effort, money and engineering expertise to come up with the CCP.

At first glance, you’d think the CCP was a CCQ that someone left in the wash and the result of the dry cycle was that it shrank. It has similar rounded contours, the same angular slide that is also not angular at the same time (a curious optical illusion) and the familiar kind of nonslip texture on the grip. Unlike the CCQ, which went through M1 and M2 versions focused on the magazine catch, the CCP comes all ready with an American-style magazine catch, which is a button behind the triggerguard. The frame has a squared triggerguard with a set of serrations and a finger hook, which is right out of the era of a “Miami Vice.” It has been a long time since I’ve seen someone shoot that way in a match, except for us old-timers, but it looks good, and it doesn’t hurt.


Walther CCP
The triggerguard is designed with a rear scallop underneath for a high grip, and the inside is dished out for thick or gloved trigger fingers.

The triggerguard is noticeably undercut to let you get your hand higher on the frame than you’d otherwise think. Out front is the now-obligatory accessory rail, where you can mount a light, laser or dual-use unit.


Walther CCP
A short accessory rail is unobtrusive and will accept compact pistol lights and laser devices for those who demand such things on their carry gun.

The magazine is a single-stack design, holding eight rounds of 9mm ammo, and it is an interesting artifact of engineering in its own right. The tube is a heavy-gauge stamping, with the main blank forming the front and sides. Then, Walther takes a stamped spine section and, fitting it to the folded front and side, presses them together into interlocking cutouts and welds them together. There are a dozen on each side of the spine, and the result is a magazine so sturdy that you could step on it and the pistol wouldn’t notice. When I jokingly mentioned that to the Walther Arms folks, their reaction was, “Go ahead, and tell us what happens.” The magazine locks open the slide when empty and drops free when the magazine-release button is pushed.

Walther CCP
G&A’s sample arrived with a pair of durable single-stack, eight-round magazines.

I have a confession to make. When it came time to fieldstrip the CCP, I spent a couple of minutes just turning it over in my hands, trying to figure out how. Not having a clue by then, I finally gave up, and despite the grievous deductions it made on my man-card, I read the instructions.

There’s a disassembly tool in the box with the pistol and spare magazine; plus, you can also use a screwdriver. I’ll bet in a short while, when a used CCP shows up in a gun shop (assuming the owners get rid of them — an unlikely event), the first question will be, “Where’s the spare magazine?” The second will be about the disassembly tool.

Unload the pistol. Dry-fire it. Push the tip of the disassembly tool against the bright tip you see in the striker assembly. Once you unlatch that, you can press the whole assembly into the slide. Retract the slide, but just far enough to clear the extractor, and lift up the slide. If you go too far, you reset the firing mechanism and have to start over. Once you get the hang of it, it’s a snap.


Walther CCP
Even well-versed gun enthusiasts may initially find the CCP unusual to disassemble, so prepare your ego if you have to consult the owner’s manual. A disassembly tool is provided in the box.

Inside, wondrous things appear. The locking system of the CCP is familiar to those who are up on their German firearms arcana. The slide has a pivoting piston pinned to it. The barrel is fixed to the frame. On the bottom of the barrel, ahead of the chamber, there is a gas port. When you fire the CCP, as the bullet passes the port, the expanding gases flow through the port and press forward on the piston. The gas pressure holds the slide closed until the thrust of the case on the slide overcomes the decreasing gas pressure holding it closed. Yep, it’s an update of the old HK P7 squeeze-cocker gas system but improved and named the Walther Softcoil technology.

Walther CCP

The advantages of the system are simple: By not using a moving barrel, Walther eliminates a hatful of surfaces that have to be machined, inspected and hand fitted. It also eliminates the vertical space needed for the unlinking/unlocking tipping barrel of the Browning system. Last, the gas pressure takes the place of the leverage of the locked-breech Browning system but also of the heavier recoil spring needed to control that system. Working the slide, there’s a slight hitch at the very beginning, coming from the striker system and its attendant safety parts, and after that the spring is quite light. If you or someone you know has low hand-strength or dexterity issues and finds the usual compact pistol difficult to use because of the heavy recoil spring found in most pistols, the CCP may be just the ticket. My wife, after 25 years of owning her own printing business, was left with reduced grip strength. Here, she has no problems working the slide of the CCP.

Walther CCP
Though unknown to most American gun owners, the re-coil spring around the barrel, pinned pivoting piston underneath and gas system sometimes appear in Europe-an pistol designs. Remember the squeeze-cocker HK P7?

The frame and the barrel and firing mechanism are intriguing bits of engineering. In the words of a novelist friend of mine, “Had I a hat, off it would be.” There are no frame rails. That’s right: The slide rides on the fixed barrel. The barrel is pinned to the gas block. The gas block and the ejector block are each pinned to the polymer housing that also holds the magazine. The part we usually call the frame is a plastic shell, a hell-for-tough durable one, but a shell nonetheless.


Walther CCP
Under the skirt of the slide, an interesting bit of engineering is revealed. No frame rails!

The serial number is on the gas block, on the shroud around the barrel. (This part is the actual firearm in the eyes of the ATF.)

Reassembly is easy. Stuff the barrel back into the recoil spring, in the slide, and run the slide back. The only fiddly part is getting the piston aligned with the gas-port tunnel, as the piston wants to flop around. I found that by holding the pistol vertically, I could watch the piston and tip the pistol until the piston was lined up. Once you get the slide back over the chamber, press the disassembly tool back into the striker assembly and the slide will snap down into place.

The safeties don’t end there. There’s a slot milled into the breech face for use as a loaded-chamber indicator. The firing mechanism has a drop safety. The CCP does not have — praise be — a magazine disconnector. Most of us don’t like them.

Walther CCP
In addition to the CCP’s onboard safety systems, a low-profile manual safety lever is present. When it’s up, it’s on Safe.

The grip is curvy, fits my hand and is comfortable to hold. It also has a thumb safety on the left rear of the frame, below the clocking serrations. My first thought was, That will never work. In the half-hour I spent handling it while doing the rough draft of this review, I picked up the CCP a number of times and flipped off the safety. I never missed it. My thumb falls right where the lever is, and the safety popped off for me every time. Getting it back on was a two-handed operation, but you don’t have to put a pistol on Safe quickly or with one hand. Getting it from Safe to Fire, yes, but getting it back, no. I found that a very pleasant and useful mirror to the way I like my 1911s set up: safety 100 percent in function but firm to take off and very hard to put back on. That way, it won’t be bumped back on inadvertently. If you don’t like thumb safeties, just don’t use it. It’s not reversible.

Walther CCP
The grip is familiar to other late-model Walther-branded pistols and comfortable for most hands to wrap around. The magazine’s floorplate adds a little extension to collect every finger.

However, the magazine catch is. The magazines are obviously made to be used right- or left-handed, and the catch is reversible. If you peer into the magazine well (unloaded, magazine out and slide locked back or slide removed from the frame), you can see a long, straight spring. Use a screwdriver to gently pry the spring up out of the notch in the magazine catch. Once it is free, pull the catch out, insert it from the other side, and pry the spring back to its former place.

Walther CCP
The rear sight is part of a three-dot sight system, laterally adjustable for windage. The front and rear sights are compatible with existing after-market night sights for the Walther P99, PPQ and PPS.

The adjustments don’t end there. The rear sight has a small opening at its base that is for the included adjustment wrench. Simply turn one way or the other to move groups left or right. Also in the box with the wrench are a couple of extra front sights. If you find that your favorite load is hitting high or low, disassemble the CCP, use the wrench to loosen and remove the Torx-head screw holding the front sight on, and replace it with one that is the correct height.

Walther CCP
Three different front sight heights are included in the box with the CCP for tuning elevation, if desired.

Test-firing the CCP was interesting. The original gas-delayed pistol, the discontinued P7, is much loved by many. I owned one back in the day and sold it. When they became available again, I snapped one up, then rediscovered why I had let go of one back then. For an all-steel pistol that weighed a pudgy 30 ounces, it had a not-fun recoil cycle. It was sharp, snappy and violent. The Walther CCP, on the other hand, wasn’t. In fact, if you went by recoil alone, you’d think you were simply shooting another tilting-barrel Browning derivative. You won’t have a clue how the system works, going by the feel. The bore height over your hand is also on the low side, so the combined effect of recoil is to make it a soft-shooting pistol, as light as it is.

The trigger, on the other hand, is curious. The system is a striker-fired variant, with a drop safety and the aforementioned thumb safety. The pull is light, with a combined effort of 5 pounds needed. However, there is a lot of “plastic-y” rubbing going on that I can feel as the trigger travels back in its arc.

Someone new to the firearms field might be tempted to describe the feel as “gritty,” “crunchy” or “jerky,” but it isn’t any of those. It is simply the impression of some plastic or polymer component rubbing on another surface. At first I was worried that this would be a hindrance to shooting groups, but it turns out not to be much, if any. Don’t get me wrong; this isn’t a match trigger, not for IPSC, IDPA or PPC. At speed, I didn’t have any impression of the trigger parts rubbing. It was only when I was focused on the front sight, working to shoot groups, that I could feel the rubbing.

As for accuracy, the CCP is certainly more than up to the task of defense. Again, I wasn’t shooting bullseye or PPC groups with it, but then it is a compact carry pistol. With a sight radius just under 5½ inches, you’re going to be hard-pressed to shoot one-hole groups with any handgun, but the CCP shot groups smaller than the apparent width of the front sight, which is gratifying.

Walther CCP

Not all is perfect. I had occasional stovepipes and failures to lock back with the Barnes ammunition. I was not at all surprised by this. The Barnes TAC-XPD is a load perfectly set up to give the CCP fits. The load is a +P, so there is more pressure to hold the slide closed. Plus, the all-copper bullets don’t need velocity to expand, so Barnes loads them to a speed that ensures expansion but keeps down pressures. This limits the momentum delivered to the slide to operate the mechanism. The simple answer is this: If your CCP doesn’t work with a particular load, don’t use that ammo. With all due respect to the Barnes, which is very good ammo, there are plenty of other options that will work perfectly in your CCP. Also, I noticed after a while shooting the CCP that the frame, or polymer housing, just above the trigger was warmer than the rest of the frame. That’s where the gas flow happens, and it will be warmer. It may even get hot if you do a lot of nonstop shooting. You also can’t use lead-bullet ammunition in the CCP, as the lead and lube will clog the gas port. Jacketed ammo only.

The standard deviation on the Hornady ammo is not a typo. I shot a second string just to be sure, and that lot in the CCP delivered an SD that was just as low both times.

A compact, lightweight, accurate single-stack 9mm with an external safety and it’s easy to work the slide? Sounds like Walther has a hot commodity in its catalog. Oh, and stomping on the magazine? All I did was make myself tired and alarm the dogs. The magazine didn’t even notice.

Walther CCP
Notes: Accuracy results are averages of four five-shot groups at 25 yards off a Sinclair front shooting rest. Velocities are averages of 10 shots measured on a PACT MKIV chronograph set 15 feet from the muzzle.

Walther CCP

  • Type: Striker fred, semiautomatic
  • Caliber: 9mm Parabellum
  • Capacity: 8+1 rds.
  • Barrel: 3.54 in.
  • Overall Length: 6.41 in.
  • Width: 1.12 in.
  • Height: 5.12 in.
  • Weight: 23 oz.
  • Finish: Stainless steel and polymer
  • Grips: N/A
  • Sights: Three dot, adjustable
  • Trigger: 5 lbs.
  • Price: $469
  • Manufacturer: Walther Arms, 479-242-8500, waltherarms.com

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Recommended Articles

See More Recommendations

Popular Videos

Cameras Don

Cameras Don't Lie: Subsonic 9mm vs. .300 Blackout

In this segment of "Cameras Don't Lie," a subsonic-ammo showdown, 9mm vs. .300 Blackout fired from AR rifles.

Guns & Ammo TV: Shooting 1,270 Yards with the 5.56 NATO

Guns & Ammo TV: Shooting 1,270 Yards with the 5.56 NATO

Guns & Ammo Rifles & Optics Editor Tom Beckstrand was on location in Idaho where he pushed the limits of the 5.56 NATO cartridge in this segment of “Long Range Tech” for Guns & Ammo TV. Pairing a SIG Sauer MCX Virtus rifle loaded with Hornady's 73-grain ELD-M ammunition, Beckstrand attempted to ring steel set at 1,270 yards, an incredible distance for any 5.56-chambered rifle and beyond the typical range for an AR-15.

Umarex Air Ruger 10/22 Rifle Review

Umarex Air Ruger 10/22 Rifle Review

In this segment of "Guns & Ammo TV," Gun Tech Editor Richard Nance and Pro-Shooter Jim Tarr head to the range to wring out the Umarex Air Ruger 10/22.

Pocket-Pistol Carry Tips and Tricks

Pocket-Pistol Carry Tips and Tricks

Pocket carry, as a method of concealed carry for a defensive firearm, can be a practical option when done right. This is especially true during the colder months when heavy outer garments can obstruct access to a traditional waistline holster. Former U.S. Navy SEAL Jeff Gonzales, president of Trident Concepts, joins G&A contributor Kimberly Heath-Chudwin to discuss guns, training and gear, including Blackhawk's TecGrip holster that can make pocket carry more successful.

See More Popular Videos

Trending Articles

The one glaring weakness in the .30-­caliber magnum cartridge lineup is best highlighted by examining the requirement around which Hornady designed the .300 PRC; the requirement came from the U.S. Special Operations Command (SOCOM). .300 PRC Review Rifle

.300 PRC Review

Tom Beckstrand - March 12, 2019

The one glaring weakness in the .30-­caliber magnum cartridge lineup is best highlighted by...

In this segment of “At The Range,” Handgunning Editor Jeremy Stafford and contributor Patrick Sweeney compare the visibility of red and green lasers in outdoor, sunny conditions. Red vs. Green Lasers: Visibility in Bright Light Accessories

Red vs. Green Lasers: Visibility in Bright Light

Guns & Ammo Staff - August 24, 2020

In this segment of “At The Range,” Handgunning Editor Jeremy Stafford and contributor Patrick...

The Pulsar Thermion XG50 Thermal Riflescope is the first-ever riflescope to combine a BAE sensor, onboard recording, automatic & manual calibration options, multiple color palettes, and manual focus.Pulsar Thermion XG50 Thermal Riflescope - First Look Optics

Pulsar Thermion XG50 Thermal Riflescope - First Look

Guns & Ammo Staff - September 02, 2020

The Pulsar Thermion XG50 Thermal Riflescope is the first-ever riflescope to combine a BAE...

From milled slides to optics-included packages, these pistol options are all red-dot sight ready.14 Red Dot Ready Pistols You Must See Handguns

14 Red Dot Ready Pistols You Must See

James Tarr - December 20, 2018

From milled slides to optics-included packages, these pistol options are all red-dot sight...

See More Trending Articles

More Reviews

The Savage Arms 110 Elite Precision is an excellent all-around rifle for most shooting activities that don't require light weight. It can be made to fit just about anyone, with a chassis that allows for accurate, rapid and effective positional shooting. And while the 110 Elite Precision is not inexpensive, it still costs less than most custom rifles. Savage Arms 110 Elite Precision Review: Excellent All-Around Rifle Reviews

Savage Arms 110 Elite Precision Review: Excellent All-Around Rifle

Proofhouse - September 15, 2020

The Savage Arms 110 Elite Precision is an excellent all-around rifle for most shooting...

It's been a while since there's been a new American-designed and -made autoloading hunting shotgun. For 2020, Savage has stepped up to the plate with the new gas-operated Renegauge series.Savage Renegauge Shotgun Review Reviews

Savage Renegauge Shotgun Review

Robert W. Hunnicutt - August 05, 2020

It's been a while since there's been a new American-designed and -made autoloading hunting...

The Nighthawk Custom Agent 2 Commander is an abbreviated version of the Agent 2, built on a forged slide and frame. The crowned muzzle is cut flush with the bushing, which was given flats around the edges. Few curves were left untouched by flats; even the bottom of the triggerguard has corners leading to the high-grip undercut. The scale motif adds striking functionality. Nighthawk Custom Agent 2 Commander Review Reviews

Nighthawk Custom Agent 2 Commander Review

Eric R. Poole - July 28, 2020

The Nighthawk Custom Agent 2 Commander is an abbreviated version of the Agent 2, built on a...

If you're in need of a pistol to bet your life on, look no further than the pistol that won over the U.S. Army, the SIG Sauer P320 - M17.Review: SIG Sauer P320 - M17 Reviews

Review: SIG Sauer P320 - M17

Richard Nance - August 14, 2020

If you're in need of a pistol to bet your life on, look no further than the pistol that won...

See More Reviews

Magazine Cover

GET THE MAGAZINE Subscribe & Save

Digital Now Included!

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW THIS MONTH'S ISSUE Arrow

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Phone Icon

Get Digital Access.

All Guns and Ammo subscribers now have digital access to their magazine content. This means you have the option to read your magazine on most popular phones and tablets.

To get started, click the link below to visit mymagnow.com and learn how to access your digital magazine.

Get Digital Access

Not a Subscriber?
Subscribe Now